Polyether_Polyether Polyol Knowledge 3-(2-furyl)-2-propenoic acid

3-(2-furyl)-2-propenoic acid

3-(2-furyl)-2-acrylic acid structural formula

Structural formula

Business number 05JQ
Molecular formula C7H6O3
Molecular weight 138.12
label

2-Furylacrylic acid,

synthetic raw materials,

Intermediates

Numbering system

CAS number:539-47-9

MDL number:MFCD00003257

EINECS number:208-718-8

RTECS number:LT8560000

BRN number:81046

PubChem number:24856659

Physical property data

1. Properties: Obtain needle crystals from water.

2. Density (g/ cm3, 25/4℃): Undetermined

3. Relative steam density (g/cm 3, air=1): Undetermined

4. Melting point (ºC): 139-141

5. Boiling point (ºC, normal pressure): 286, 117ºC (1.06kpa)

6. Boiling point (ºC, 8kPa): Undetermined

7. Refractive index: Undetermined

8. Flash point (ºF) : 286

9. Specific rotation (º): Undetermined

10. Autoignition point or ignition temperature (ºC): Undetermined

11. Vapor pressure (kPa, 25ºC): Undetermined

12. Saturated vapor pressure (kPa, 55.1ºC): Undetermined

13. Heat of combustion (KJ/mol): Undetermined

14. Critical temperature (ºC): Undetermined

15. Critical pressure (KPa): Undetermined

16. Oil and water (octanol/water) Log value of distribution coefficient: Undetermined

17. Explosion upper limit (%, V/V): Undetermined

18. Explosion lower limit (%, V/V): Undetermined

19. Solubility: Easily soluble in ethanol and ether.

Toxicological data

1. Acute toxicity: mouse intraperitoneal LD50: 276mg/kg, no detailed description except the lethal dose;

2. Mutagenicity data: TEST system mutation of microbial organism: bacteria – Salmonella typhimurium Bacillus sp.: 10 ug/plate;

Ecological data

This substance may be harmful to the environment, and special attention should be paid to water bodies.

Molecular structure data

1. Molar refractive index: 36.00

2. Molar volume (cm3/mol): 107.8

3. Isotonic specific volume (90.2K ): 286.0

4. Surface tension (dyne/cm): 49.4

5. Polarizability (10-24cm3): 14.27

Compute chemical data

1. Hydrophobic parameter calculation reference value (XlogP): 1.2

2. Number of hydrogen bond donors: 1

3. Number of hydrogen bond acceptors: 3

4. Number of rotatable chemical bonds: 2

5. Number of tautomers:

6. Topological molecular polar surface area (TPSA): 50.4

7. Number of heavy atoms: 10

8. Surface charge: 0

9. Complexity: 151

10. Number of isotope atoms: 0

11. Determine the number of atomic stereocenters: 0

12. Uncertain number of atomic stereocenters: 0

13. Determine the number of chemical bond stereocenters: 1

14. The number of uncertain chemical bond stereocenters: 0

15. The number of covalent bonding units: 1

Properties and stability

1. Use and store according to specifications. It will not decompose and avoid contact with oxides.

2. Exist in smoke.

Storage method

Stored in a cool, dry and well-ventilated warehouse. Keep away from fire and heat sources. Protect from direct sunlight. The packaging is sealed. They should be stored separately from acids and food chemicals, and avoid mixed storage. Suitable materials should be available in the storage area to contain spills.

Synthesis method

1. Obtained from the reaction of furfural and malonic acid. Add furfural and malonic acid to pyridine, heat to reflux for 2 hours, cool, add water, and add concentrated ammonia while stirring until the acid is almost completely dissolved. Filter the solution, wash the filter cake with a small amount of water, combine the filtrate and washing liquid, acidify with hydrochloric acid, and then heat on a boiling water bath for 1.5-2 hours. The precipitated precipitate is filtered out, washed with water, and dried to obtain the finished product, with a yield of 90-92%. 2. Obtained from the oxidation of furanoacrolein [623-30-3] and acid precipitation. Add the mixture of water, furanocrolein, silver oxide and water to the reaction pot, and introduce oxygen at about 25°C while stirring. After 10 minutes, add 35-50% sodium hydroxide solution dropwise, add 1/2 of the amount within 1 hour, and the temperature is lower than 40°C. Add the other half of the sodium hydroxide solution within 10 minutes, then add oxygen for 10 minutes, and control the pH to 11-12, cool to below 40℃, discharge and filter. The filter cake is silver oxide and is applied after washing. Adjust the washed and filtrate to pH 3 with hydrochloric acid, heat to 90°C to dissolve all the precipitated furanoacrylic acid crystals, then cool to 30°C to precipitate the crystals, filter, wash with ice water, and dry to obtain furanoacrylic acid. 3. Obtained from the condensation of furfural and acetic anhydride. In a dry reaction pot, add acetic anhydride, furfural and anhydrous sodium acetate, stir and reflux at 150°C for 7 hours, add crushed ice, and filter out the crude product. The crude product is suspended in hot water and heated, and alkali is added to adjust the pH to 5.9-6. After the crude product is completely dissolved, add activated carbon to decolorize at 90°C, filter, adjust the filtrate to pH 3 with hydrochloric acid at 50-60°C, precipitate crystals, filter, wash with water, and dry to obtain furanoacrylic acid. In addition, furfural and acetone are condensed in a sodium hydroxide solution to first obtain furfurylidene acetone, and then oxidized with bleaching powder to obtain the product, with a yield of more than 65%.

Purpose

Furanoacrylic acid is an intermediate for furopyramide, a drug used to treat schistosomiasis. It is also used to prepare heptanedioic acid, pimelic acid, vinyl furan and its esters, etc.

This article is from the Internet, does not represent the position of Toluene diisocyanate reproduced please specify the source.https://www.polyether-factory.com/archives/19777

author:

Previous article
Next article
Contact Us

Contact us

+86 - 152 2121 6908

Online consultation: QQ交谈

E-mail: sales@newtopchem.com

Working hours: Monday to Friday, 9:00-17:30, closed on holidays
Follow wechat
Scan wechat and follow us

Scan wechat and follow us

Follow Weibo
Back to top
Home
E-mail
Products
Search