dibutyl sulfate

Dibutyl sulfate structural formula

Structural formula

Business number 06RQ
Molecular formula C8H18O4S
Molecular weight 210.29
label

n-butyl sulfate,

dibutyl sulfate,

Butyl sulfate,

Dibutyl sulfate,

(CH3CH2CH2CH2O)2SO2

Numbering system

CAS number:625-22-9

MDL number:MFCD00059420

EINECS number:None

RTECS number:WS7700000

BRN number:1707498

PubChem ID:None

Physical property data

1. Properties: colorless liquid.

2. Density (g/mL, 25/4℃): 1.06

3. Relative vapor density (g/mL, air=1): Undetermined

4. Melting point (ºC): Undetermined

5. Boiling point (ºC, normal pressure): Undetermined

6. Boiling point (ºC, 5.2kPa): Undetermined

7. Refractive index: 1.421

8. Flash point (ºC): Undetermined

9. Specific rotation (º): Undetermined

p>

10. Autoignition point or ignition temperature (ºC): Undetermined

11. Vapor pressure (kPa, 25ºC): Undetermined

12. Saturated vapor pressure (kPa, 60ºC): Undetermined

13. Heat of combustion (KJ/mol): Undetermined

14. Critical temperature (ºC): Undetermined

15. Critical pressure (KPa): Undetermined

16. Log value of oil-water (octanol/water) partition coefficient: Undetermined

17. Explosion upper limit (%, V /V): Undetermined

18. Lower explosion limit (%, V/V): Undetermined

19. Solubility: Insoluble in water.

Toxicological data

1. Acute toxicity: Rat (oral) TDLo: 12mg/kg

Rat (subcutaneous) TDLo: 9,500mg/kg

Since the LD50 of table salt is 3,000 mg /kg, the acute toxicity level of BPA is the same as that of table salt.

Ecological data

Do not allow large quantities of products that are slightly harmful to water to come into contact with groundwater, waterways or sewage systems. Do not discharge materials into the surrounding environment without government permission.

Molecular structure data

1. Molar refractive index: 51.38

2. Molar volume (cm3/mol): 194.3

3. Isotonic specific volume (90.2K ): 472.9

4. Surface tension (dyne/cm): 35.0

5. Polarizability (10-24cm3): 20.37

�Calculate chemical data

1. Hydrophobic parameter calculation reference value (XlogP): 2.2

2. Number of hydrogen bond donors: 0

3. Number of hydrogen bond acceptors: 4

4. Number of rotatable chemical bonds: 8

5. Topological molecular polar surface area (TPSA): 52.6

6. Number of heavy atoms: 13

7. Surface charge: 0

8. Complexity: 177

9. Number of isotope atoms: 0

10. Determine the number of atomic stereocenters : 0

11. Uncertain number of atomic stereocenters: 0

12. Determined number of chemical bond stereocenters: 0

13. Uncertain chemical bond formation Number of structural centers: 0

14. Number of covalent bond units: 1

Properties and stability

Keep away from oxides.

Storage method

Store in an airtight container in a cool, dry place. Store away from oxidizing agents.

Synthesis method

1. The reaction between dibutyl sulfite and sulfuryl chloride requires cooling at the beginning. The reaction device should have good reflux condensation equipment. After a large amount of sulfur dioxide is released, the temperature is then raised to 130-135°C to allow the sulfur dioxide to escape. The reaction product is distilled under reduced pressure to obtain dibutyl sulfate.

2. Preparation method:

In a stirrer, thermometer, dropping funnel, and reflux condenser (with a gas pipe connected to the top to the sulfur dioxide absorption device), add sulfite Take 625g (3.2mol) of n-butyl ester (2), cool it in a water bath, slowly add 217g (1.6mol) of sulfuryl chloride dropwise, and finish the addition in about 0.5h. After adding, slowly heat until the generated 1-chlorobutane refluxes (about 100~110℃). At this time, a large amount of sulfur dioxide escapes. Change to a distillation device for distillation, and slowly heat it to raise the internal temperature to 130-135°C until there is basically no sulfur dioxide or 1-chlorobutane steaming out. Cool to room temperature, add 100 mL of saturated sodium carbonate solution, stir thoroughly, separate the organic layer, dry with anhydrous calcium chloride, then add anhydrous sodium carbonate and leave it for 1 day. Distill under reduced pressure twice, collect the fraction at 109~111℃/0.53kPa, and obtain 250g of di-n-butyl sulfate (1), with a yield of 74%. Note: ① Refer to the above method and use di-n-propyl sulfite instead of di-n-butyl sulfite to prepare di-n-propyl sulfate (C6H14O4S), bp88~91℃/0.53kPa, yield 66~70%. [1]

Purpose

Organic intermediates.

This article is from the Internet, does not represent the position of Toluene diisocyanate reproduced please specify the source.https://www.polyether-factory.com/archives/20036

author:

Previous article
Next article
Contact Us

Contact us

+86 - 152 2121 6908

Online consultation: QQ交谈

E-mail: sales@newtopchem.com

Working hours: Monday to Friday, 9:00-17:30, closed on holidays
Follow wechat
Scan wechat and follow us

Scan wechat and follow us

Follow Weibo
Back to top
Home
E-mail
Products
Search