Polyether_Polyether Polyol Knowledge Stearamide Stearamide

Stearamide Stearamide

Stearylamide Structural Formula

Structural formula

Business number 03J2
Molecular formula C18H37NO
Molecular weight 283.49
label

stearamide,

Saturated octadecylamide,

Octadecanamide,

Stearamide,

Lubricants and release agents,

Smooth agent for polyolefins,

Film anti-blocking agent,

Mixing agents for inks and crayons

Numbering system

CAS number:124-26-5

MDL number:MFCD00008038

EINECS number:204-693-2

RTECS number:RG0182000

BRN number:909006

PubChem number:24898031

Physical property data

1. Properties: white or light yellow powder

2. Density (g/mL, 25/4℃): 0.96

3. Melting point (ºC) : 108.5109℃

4. Boiling point (ºC, 1596Pa): 250~251

5. Solubility: miscible with paraffin, soluble in hot ethanol, chloroform, and ether, insoluble in cold ethanol, and insoluble in water.

6. Relative density (20ºC/4 ºC): 0.96

Toxicological data

1. Tumor-causing: mice injected with TDLO: 1000mg/kg

Ecological data

None

Molecular structure data

1. Molar refractive index: 89.00

2. Molar volume (cm3/mol): 326.4

3. Isotonic specific volume (90.2K): 782.3

4. Surface tension (dyne/cm): 32.9

5. Polarizability (10-24cm3): 35.28

Compute chemical data

1. Reference value for hydrophobic parameter calculation (XlogP): None

2. Number of hydrogen bond donors: 1

3. Number of hydrogen bond acceptors: 1

4. Number of rotatable chemical bonds: 16

5. Number of tautomers: 3

6. Topological molecule polar surface area 43.1

7. Number of heavy atoms: 20

8. Surface charge: 0

9. Complexity: 204

10. Number of isotope atoms: 0

11. Determine the number of atomic stereocenters: 0

12. Uncertain number of atomic stereocenters: 0

13. Determine the number of chemical bond stereocenters: 0

14. Number of uncertain chemical bond stereocenters: 0

15. Number of covalent bond units: 1

Properties and stability

1. Non-hygroscopic, good slipperiness, can improve the dispersion effect of pigments and dyes, and has lubricity and demoulding properties.

2. This product is white or light yellow and fades.��Powder. After recrystallization in ethanol, it becomes colorless leaf-like crystals. Soluble in hot ethanol, chloroform, ether, insoluble in cold ethanol, insoluble in water. The lubricity is lower than grease and the durability is shorter. Thermal stability is poor and there is initial coloration. Combining with a small amount of higher alcohol (C16-18) can overcome the above shortcomings.

Storage method

Woven bag packaging lined with plastic bags. Store in a cool, ventilated and dry place, protected from moisture and sun.

Synthesis method

1. Put 1 mol of stearic acid into the reaction kettle and heat to melt. Continue to raise the temperature to 200°C with stirring, and begin to introduce ammonia gas. Ammonia gas is introduced from the bottom of the kettle to speed up the stirring speed and strengthen the contact between gas and liquid. By-product water and unreacted ammonia enter the recovery device through the condensation system. When ammonia gas is introduced which is twice the mass fraction of stearic acid, take a gas sample and check. If the gas no longer contains water, the reaction has reached the end point. Stop passing ammonia and discharge the material while it is hot for processing and shaping. Dissolve it in ethanol, add activated carbon to decolorize it, filter it while it’s hot, cool it for crystallization, wash the crystals with water, and dry them to get the pure product.

Purpose

1. It can be used as a lubricant and release agent in the processing of plastics such as polyvinyl chloride, polystyrene, urea-formaldehyde resin, etc. It has excellent external lubrication effect and release performance, and has good transparency and electrical insulation, but Poor stability. It can also be used as a slip agent for polyolefin plastics, an anti-adhesive agent for films, an internal lubricant for natural and synthetic rubber, and a waterproof softener for fibers. When used in rubber processing, it can improve the processability of the rubber compound, improve the dispersion effect of various additives, and give the product a good gloss. 2. This product can also be used as a slip agent for polyolefins, an anti-adhesive agent for films, and a compounding agent for inks and colored crayons.

This article is from the Internet, does not represent the position of Toluene diisocyanate reproduced please specify the source.https://www.polyether-factory.com/archives/16740

author:

Previous article
Next article
Contact Us

Contact us

+86 - 152 2121 6908

Online consultation: QQ交谈

E-mail: sales@newtopchem.com

Working hours: Monday to Friday, 9:00-17:30, closed on holidays
Follow wechat
Scan wechat and follow us

Scan wechat and follow us

Follow Weibo
Back to top
Home
E-mail
Products
Search